2. — 2 —
DSC-S60/S80/S90/ST80
Camera
[System]
Image device 6.85 mm (1/2.7 type) color
CCD, Primary color filter
Total pixel number of camera
Approx. 4 231 000 pixels
Effective pixel number of camera
Approx. 4 065 000 pixels
Lens Carl Zeiss Vario-Tessar
3× zoom lens
f = 6.0 - 18.0 mm (39 - 117 mm
when converted to a 35 mm still
camera)
F2.8 - 5.2
Exposure control Automatic exposure, Manual
exposure, Scene Selection (7
modes)
White balance Automatic, Daylight, Cloudy,
Fluorescent, Incandescent
File format (DCF compliant)
Still images: Exif Ver. 2.2
JPEG compliant, DPOF
compatible
Movies: MPEG1 compliant
(Monaural)
Recording media Internal memory 32 MB
“Memory Stick”
Flash Recommended distance (ISO
set to Auto): 0.2 m to 4.5 m
(7 7/8 inches to 178 1/2 inches)
(W)/0.5 m to 2.5 m
(19 3/4 inches to 98 1/2 inches)
(T)
[Input and Output connectors]
Multi connector
USB communication
Hi-Speed USB (USB 2.0
compliant)
[LCD screen]
LCD panel DSC-S90:
6.2 cm (2.5 type) TFT drive
DSC-S80/ST80/S60:
5.1 cm (2.0 type) TFT drive
Total number of dots
115 200 (480×240) dots
[Power, general]
Power HR15/51:HR6 (Size AA)
Nickel-Metal Hydride batteries
(2) (supplied with DSC-S90/
S80), 2.4 V
R6 (size AA) Alkaline batteries
(2) (supplied with DSC-S60),
3 V
Battery pack NP-NH25 (1)
(supplied with DSC-ST80)
ZR6 (size AA) Oxy Nickel
Primary Battery (2) (not
supplied), 3 V
AC-LS5K AC Adaptor (not
supplied), 4.2 V
Power consumption
(during shooting with the LCD screen on)
DSC-S90: 1.1 W
DSC-S80/ST80/S60: 1.0 W
Operating temperature
0°C to +40°C (+32°F to
+104°F)
Storage temperature
–20°C to +60°C (–4°F to
+140°F)
Dimensions 96.6×64.4×40.1 mm
(3 7/8×2 5/8×1 5/8 inches)
(W/H/D, excluding maximum
protrusions)
Mass DSC-S90:
Approx. 253 g (8 oz) (including
two batterries and wrist strap)
DSC-S80/ST80/S60:
Approx. 249 g (8 oz) (including
two batterries and wrist strap)
Microphone Electret condenser microphone
Speaker Dynamic speaker
Exif Print Compatible
PRINT Image Matching III
Compatible
PictBridge Compatible
SPECIFICATIONS
BC-CS2A/CS2B Ni-MH battery charger
(supplied with DSC-S90/S80)
Power requirements
AC 100 to 240 V, 50/60 Hz,
3 W
Output voltage AA: DC 1.4V 400 mA × 2
AAA: DC 1.4 V 160 mA × 2
Operating temperature
0°C to +40°C (+32°F to
+104°F)
Storage temperature
–20°C to +60°C (–4°F to
+140°F)
Dimensions Approx. 71×30×91 mm
(2 7/8×1 3/16×3 5/8 inches)
(W/H/D)
Mass Approx. 90 g (3 oz)
Design and specifications are subject to change
without notice.
(supplied with DSC-ST80)
(supplied with DSC-ST80)
Cyber-shot Station CSS-SA
[Input/Output connectors]
A/V OUT (MONO) jack (Monaural)
Minijack
Video*: 1 Vp-p, 75 Ω, unbalanced,
sync negative
Audio*: 327 mV (47 kΩ loaded)
Output impedance: 2.2 kΩ
* When the DSC-S90/S80/ST80/S60 is
connected.
USB jack: B
DC IN jack
Multi connector
[General]
Dimensions (Approx.):
120 × 36 × 89 mm
(4 3/4 × 1 7/16 × 3 5/8 inches)
(w/h/d)
Mass (Approx.): 120 g (4.3 oz)
Operating temperature:
0 °C to +40 °C (32 °F to +104 °F)
Storage temperature:
–20 °C to +60 °C (–4 °F to +140 °F)
AC Adaptor AC-LS5
Input rating:
100 V to 240 V AC 50/60 Hz
Output rating:
4.2 V DC
See the label on the AC Adaptor for
other specifications.
Dimensions (Approx.):
48 × 29 × 81 mm
(1 15/16 × 1 3/16 × 3 1/4 inches)
(w/h/d, excluding projecting parts)
Mass (Approx.):
130 g (5 oz) excluding AC Power cord
Operating temperature:
0 °C to +40 °C (32 °F to +104 °F)
Storage temperature:
–20 °C to +60 °C (–4 °F to +140 °F)
Rechargeable battery pack NP-NH25
(supplied with DSC-ST80)
Normal voltage:
1.2 V × 2
Capacity:
typ. 2,500 mAh
Operating temperature:
0 °C to +40 °C (32 °F to +104 °F)
3. — 3 —
DSC-S60/S80/S90/ST80
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINEWITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
1. Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
2. Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
4. Look for parts which, through functioning, show obvious signs
of deterioration. Point them out to the customer and
recommend their replacement.
5. Check the B+ voltage to see it is at the values specified.
6. FLEXIBLE Circuit Board Repairing
• Keep the temperature of the soldering iron around 270°C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
Unleaded solder
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Table for differences of function
Model DSC-S60 DSC-S80 DSC-S90 DSC-ST80
US, CND, AEP, UK,
AEP, UK, E,
US, CND, AEP, UK,
Destination E, AUS, HK,
AUS, HK, KR
E, AUS, HK, AEP, UK, E, HK
CH, KR, JE CH, KR, AR, JE
LCD panel size 2.0 type 2.0 type 2.5 type 2.0 type
• Abbreviation
AR : Argentine model
AUS : Australian model
CH : Chinese model
CND : Canadian model
HK : Hong Kong model
JE : Tourist model
KR : Korea model
Ver 1.1 2005.07
4. — 4 —
DSC-S60/S80/S90/ST80
TABLE OF CONTENTS
1. SERVICE NOTE
1-1. Note for Repair ································································1-1
1-2. Discharging of The ST-122 Flexible Board’s Charging
Capacitor (C003) ·····························································1-1
1-3. Note in Lens Frame Installation ······································1-2
1-4. Description on Self-diagnosis Display ····························1-2
1-5. Method for Copying or Erasing the Data in Internal
Memory ···········································································1-3
1-6. Process After Fixing Flash Error ·····································1-4
2. DISASSEMBLY
2-1. Disassembly·····································································2-1
2-2. SY-126 Board Service Position ·······································2-5
2-3. Removal of Barrier Unit ··················································2-7
2-4. Circuit Boards Location ··················································2-8
3. BLOCK DIAGRAMS
3-1. Overall Block Diagram (1/2) ···········································3-1
3-2. Overall Block Diagram (2/2) ···········································3-3
3-3. Power Block Diagram (1/2)·············································3-5
3-4. Power Block Diagram (2/2)·············································3-7
4. PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS
4-1. Frame Schematic Diagram ··············································4-1
4-2. Schematic Diagrams ························································4-5
CD-573 BOARD (CCD IMAGER) ·································4-7
SW-446 BOARD
(CONTROL SWITCH, LCD PANEL) ··························4-27
ST-122 FLEXIBLE (FLASH DRIVE) ··························4-29
MC-153 FLEXIBLE (MULTI CONNECTOR) ············4-31
MS-271 BOARD
(MEMORY STICK CONNECTOR)·····························4-33
CONTROL SWITCH BLOCK ·····································4-34
4-3. Printed Wiring Boards ···················································4-35
CD-573 ··········································································4-37
SW-446 ··········································································4-41
ST-122 FLEXIBLE ·······················································4-43
MC-153 FLEXIBLE······················································4-43
MS-271 ··········································································4-45
4-5. Mounted Parts Location ················································4-50
5. REPAIR PARTS LIST
5-1. Exploded Views ·······························································5-2
5-1-1.Cabinet Section································································5-2
5-1-2.Main Block Assembly ·····················································5-3
5-1-3.Lens Block Assembly ······················································5-4
5-2. Electrical Parts List ·························································5-5
Section Title Page
Ver 1.1 2005.07
5. 1-1
DSC-S60/S80/S90/ST80
1-2. DISCHARGING OF THE ST-122
FLEXIBLE BOARD’S CHARGING
CAPACITOR (C003)
The charging capacitor (C003) of ST-122 flexible board is charged
up to the maximum 300 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of a
resistor of 1 kΩ /1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to prevent
electrical shock.
1 kΩ/1 W
Wrap insulating tape.
Discharging the Capacitor
Short-circuit between the positive and the negative terminals of
charged capacitor with the short jig about 10 seconds.
1-1. NOTE FOR REPAIR
Make sure that the flat cable and flexible board are not cracked of
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
When remove a connector, don’t pull at wire of connector.
It is possible that a wire is snapped.
When installing a connector, don’t press down at wire of connector.
It is possible that a wire is snapped.
1. SERVICE NOTE
R:1 kΩ/1 W
(Part code:
1-215-869-11)
6. 1-2
DSC-S60/S80/S90/ST80
1-3. NOTE IN LENS FRAME INSTALLATION
When tightening a screw, have both sides of the lens block assembly so as not for the load to depend.
Self-diagnosis display
• C: ss: ss
You can reverse the camera
malfunction yourself. (However,
contact your Sony dealer or local
authorized Sony service facility
when you cannot recover from the
camera malfunction.)
• E: ss: ss
Contact your Sony dealer or local
authorized Sony service facility.
Display Code
C:32:ss
C:13:ss
Countermeasure
Turn the power off and on again.
Format the “Memory Stick” or internal
memory.
Cause
Trouble with hardware.
“Memory Stick” or internal memory is
unformatted.
Caution Display During Error
SYSTEM ERROR
FORMAT ERROR
MEMORY STICK ERROR
E:61:ss
E:91:ss
E:92:ss
1-4. DESCRIPTION ON SELF-DIAGNOSIS DISPLAY
Insert a new “Memory Stick”. “Memory Stick” is broken.
Turn the power off and on again. Trouble with internal memory. INTERNAL MEMORY ERROR
Checking of lens drive circuit. When failed in the focus and zoom
initialization.
—
Checking of flash unit or replacement
of flash unit. (Note)
Insert batteries correctly.
Abnormality when flash is being
charged.
Batteries are not inserted correctly.
Note: After repair, be sure to perfom “1-6. PROCESS AFTER FIXING FLASH ERROR”.
Tapping screw
Lens block assembly
Lens flame
7. 1-3
DSC-S60/S80/S90/ST80
1-5. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY
The data can be copied/erased by the operations on the Setup screen. (When erasing the data, execute formatting the internal memory.)
Note: 1 When replacing the SY-126 board, erase the data in internal memory of the board before replacement.
Note: 2 When replacing the SY-126 board or the IC301 on the SY-126 board, execute formatting and initialize the internal memory after
replacement.
Method for Copying the Data in Internal Memory
Method for Formatting the Internal Memory
Formats the internal memory.
• Note that formatting irrevocably erases all data in the internal memory, including even protected images.
1 Select [OK] with v on the control button, then press z.
The message “All data in internal memory will be erased Ready?” appears.
2 Select [OK] with v, then press z.
The format is complete.
Format
OK See the following procedure.
Cancel Cancels the formatting.
Copies all images in the internal memory to a “Memory Stick”.
1 Insert a “Memory Stick” having 32 MB or larger capacity.
2 Select [OK] with v on the control button, then press z.
The message “All data in internal memory will be copied Ready?” appears.
3 Select [OK] with v, then press z.
Copying starts.
• Use batteries with enough capacity or the AC Adaptor (not supplied). If you attempt to copy image files
using batteries with little remaining charge, the batteries may run out, causing copying to fail or possibly
corrupting the data.
• You cannot copy individual images.
• The original images in the internal memory are retained even after copying. To delete the contents of the
internal memory, remove the “Memory Stick” after copying, then execute the [Format] command in
Internal Memory Tool.
• You cannot select a folder copied on a “Memory Stick”.
• The setting of (Print order) marks is not copied even when you copy data.
Copy
OK See the following procedure.
Cancel Cancels the copying.
Copying
102_COPY
8. 1-4E
DSC-S60/S80/S90/ST80
1-6. PROCESS AFTER FIXING FLASH ERROR
When “FLASH error” (Self-diagnosis Code E : 91 : ** ) occurs, to prevent any abnormal situation caused by high voltage, setting of the
flash is changed automatically to disabling charge and flash setting.
After fixing, this setting needs to be deactivated. Flash error code can be initialized by the operations on the Setup screen.
Method for Initializing the Flash Error Code
Initializes the setting to the default setting.
1 Select [OK] with v on the control button, then press z.
The message “Initialize all settings Ready?” appears.
2 Select [OK] with v, then press z.
The settings are reset to the default setting.
• Make sure that the power is not disconnected during resetting.
Initialize
OK See the following procedure.
Cancel Cancels the resetting.
Ver 1.1 2005.07
9. DSC-S60/S80/S90/ST80
2-1 2-2
The following flow chart shows the disassembly procedure.
2-1. DISASSEMBLY
2. DISASSEMBLY
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between the two
points with the short jig about 10
seconds.
14
2
5
6
1 Open the BT lid.
2 Screw (M1.7) x1
3 Screw (M1.7) x3
4 Close the BT lid.
5 Claw x1
6 Claw x1
7 Claw x3
8 Cabinet (rear) block
9 Claw x1
0 Claw x2
qa Cabinet (front) block
1 Claw x4
2 Control switch block
1 Flexible board: CN702
2 Slide the cabinet (upper) to
upper side and remove claw.
3 Claw x1
4 Claw x1
5 Cabinet (upper) block
6 Mic harness: CN703
1 Claw x1
2 Claw x1
3 Lift the ST holder.
4 Flexible board of D002 section
5 Claw x2
6 Flexible board of flash unit section
1 Screw (M1.7) x1
2 Flexible board of BT001 section
3 Flexible board of SP901 section
4 Claw x2
5 Claw x2
6 Flexible board: CN701
7 MC-153
2
1
3
5
6
4
2
3
1
1
4
2
5
5
3
5
6
4
9
0
7
7
3
3
3
8
qa
1 Turn lens ring to the position
which the line of lens ring and
the line of front cabinet suit.
2 Lens ring
Line
Line
1
2
7
6
1 1
2
Note: Mic harness is connected.
Note: Speaker adhesive sheet
cannot be recycle.
HELP
HELP
Speaker adhesive sheet
R:1 kΩ/1 W
(Part code:
1-215-869-11)
to Page 2-3
Barrier unit
(Refer to page 2-7)
11. DSC-S60/S80/S90/ST80
14
2
5
6
9
0
7
7
3
3
3
8
qa
2
1
3
5
6
4
2
3
1
1
4
2
5
5
3
5
6
4
7
6
5
1 2
3
4
4
4
A
S90 S60/S80/ST80
1
2
1
1
1 2
3
1
2
8
5
7
3
3
6
6
4
8
4
7
3
3
6
5
5
6
6
7
4
Connection cord (DK-2AA)
(1-830-351-11)
Lens block
MC-153 flexible
SY-126 board
SW-446 board
D901, LCD901
(Note)
Cabinet (upper) block
(Control switch block)
MS-271 board
AC power
adaptor
AC IN
ST-122 flexible
BT901
Color monitor
A/V multi cable
(Note)
2-5 2-6
2-2. SY-126 BOARD SERVICE POSITION
Note: If the A/V multi cable is connected to the multi connector
of MC-153 flexible board, the image can not appear on the
LCD screen.
If you want to confirm the circuit of LCD drive or LCD,
disconnect the A/V multi cable.
12. DSC-S60/S80/S90/ST80
2-7 2-8E
2-3. REMOVAL OF BARRIER UNIT
[BARRIER OPERATION TEST METHOD]
After the barrier unit is replaced, check the following items with turning the power of the set ON/OFF.
• The lens moves out and the barrier shutters open completely when the power is turned on.
• The lens moves in and the barrier shutters close completely when the power is turned off.
Checking condition is 1 downward 2 45° downward 3 horizontal 4 45° upward 5 upward; totally five positions
and check three times for each position.
The test needs to be performed only when the barrier unit is replaced.
No performance of this test is needed when the lens is replaced.
1 downward 2 45° downward 3 horizontal 4 45° upward 5 upward
3X
3
X
3X
3
X
3X
1 Switch on a power supply.
3 Switch off a power supply by taking out a battery
or cut off a power supply from AC daptor.
(without using camera's power swich)
4 Pinch A portion with finger
and fit a driver over a hollow.
A
2 Push zoom button and transform the lens
as shown below.
5 Ornamental fixed plate (A)
7 Barrier unit
6 Two screws
(M1.4 × 4.5)
2-4. CIRCUIT BOARDS LOCATION
Board Name Function
CD-573 CCD IMAGER
CH-169 CCD SIGNAL PROCESS
(included in SY-126)
MC-153 flexible MULTI CONNECTOR
MS-271 MEMORY STICK CONNECTOR
ST-122 flexible FLASH DRIVE
SW-446 CONTROL SWITCH, LCD PANEL
SY-126 CAMERA MODULE, CAMERA DSP, CPU,
(including CP401 LENS DRIVE, BURST FLASH, SDRAM, AND FLASH,
(CH-169 board)) AUDIO, DC/DC CONVERTER, CONNECTOR
CD-573
SY-126
(including CP401 (CH-169 board))
SW-446
ST-122 flexible
MS-271
MC-153 flexible
CH-169
(included in SY-126)
13. HELP
DSC-S60/S80/S90/ST80
Control switch block
Mic harness
MC-153 flexible board (BT001 section)
MC-153 flexible board
(BT001 section)
Mic harness
Mic harness
- Top side -
- Bottom side -
Control switch block
MIC901
Two claws
MIC901
HELP
Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown.
14. DSC-S60/S80/S90/ST80
Link
Link
3. BLOCK DIAGRAMS
POWER BLOCK DIAGRAM (1/2)
OVERALL BLOCK DIAGRAM (2/2) POWER BLOCK DIAGRAM (2/2)
OVERALL BLOCK DIAGRAM (1/2) POWER BLOCK DIAGRAM (1/2)
OVERALL BLOCK DIAGRAM (2/2) POWER BLOCK DIAGRAM (2/2)
OVERALL BLOCK DIAGRAM (1/2)
15. DSC-S60/S80/S90/ST80
3-1. OVERALL BLOCK DIAGRAM (1/2)
3-1 3-2
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
3. BLOCK DIAGRAMS
ST-122 FLEXIBLE BOARD (1/2)
SY-126 BOARD (1/2)
SAN AUOUT
XCS FE
XSAN RST OUT
XSAN RST OUT
XSAN RST OUT
VSUB CONT PRE
F2
U22
E1
R23
2
OVERALL (2/2)
(PAGE 3-3)
USB DP, USB DM
AF4
K26
L26
K5 G4 H4
L5 H2 H1
J1 J2 M5
J4 K4 M6
K2 K1
AC1
AD1
A : VIDEO SIGNAL
A : AUDIO SIGNAL
A : VIDEO/AUDIO SIGNAL
D901
BACKLIGHT
COLOR
LCD
PANEL
U2
R6
BL H
21
ı
28
CN003
CN004
LCD901
6
5
2
1
HSYNC, VSYNC, DCLK
CLKTGO
U4
R4
R5
R25
MSHUT EN,
MSHUT DIR
IRIS S EN, IRIS S IN,
IRIS M EN, IRIS M IN
ZM EN,
ZM DIR A,
ZM DIR B
IC101
(1/2)
XCS
USB DPULLUP
PANEL UNIT
SAN AUIN
CAMERA DSP, CPU
LENS CONTROL,
MODE CONTROL
(2/8)
J5
05
V23
R22
AB22
Y26
T5
XCS AUDIO
USB VBUS
D8 D7
E8 E7
D6 D5
E6 B4
AB6 AC4
AE4 AE5
AC5 AF6
BL H
BL L
OVERALL (2/2)
(PAGE 3-4)
1
BL L
BL H
4
CN005 (1/2)
CN706
(1/2)
BL L
2
30
6
28
28
6
5
29
32
W25
XRESET
LCD HD, LCD VD, LCD CK
XCS PANEL
XSAN RST OUT
CA FD
H5
CA HD
40
41
SAN1 SO, XSAN1 SCK
SAN1 SO, XSAN1 SCK
SAN1 SO, XSAN1 SCK
STRB CHG
XSTRB FULL
ST UNREG
Q001
FLASH
UNIT
FLASH
CONTROL,
CHARGE
CONTROL
6
9
10
7
IC002
XE_A(H)
TRIGGER
XE_K(L)
CHARGE+
CHARGE-
+
C003
CHARGING
CAPACITOR
D001
3
5 4
1
15
T001
STRB CHG CONT
4
STRB ON
N2
N6
M2
SW-446 BOARD (1/2)
CA AD00 – CA AD13 LCD D0 – LCD D7
SAN1 SO, XSAN1 SCK
MS BS, MS D0 – MS D3, MS CLK
Q101
CPU
D0
–
CPU
D15
CPU
D0
–
CPU
D15
XCPU CS4
IC201
32M BURST FLASH
(4/8)
IC203
128M SDRAM
(4/8)
IC301
32M AND FLASH
(5/8)
K3 J3 G3 H7 H9 G6 G9
F7 E8 D10 D9
H8 H10 G8 G10
E7 E9 D7 E10
AB13 AA13 AE13 AF13
AF12 AE12 AA12 AC12
AC11 AB12 AE11 AF11
AE10 AB11 AC10 AB10
F7 E6 E5 G5
E4 G3 E3 G1
G7 F6 F5 F4
D5 F3 F2 E2
E8 D8 C8 B8 A8 B7 A7
C7 A2 B2 C2 A1 B1 C1
D2 D1 D4 B6 A6 C6 B3
AF21 AF20 AE20 AB18 AB19 AC19 AB16
AE19 AF19 AF18 AE18 AA15 AC18 AC17
AB15 AE17 AF17 AE16 AB14 AC16 AC15 AE14
B5
K10
AC6
XCPU CS0
E7
SAN 27M CLKO
B4
AE6
AF9
DSP QCLK
71
DSP QCLKE
70
A18
A17
F4
CPU A01 – CPU A21, CPU A25
CPU D0 – CPU D15
CPU
A01
–
CPU
A21
CPU
A20,
A21,
A25
DSP DQ00 – DSP DQ31, DSP DQM0 – DSP DQM3
DSP AQ00 – DSP AQ11, DSP QBA0, DSP QBA1
3 5 6 8 9 11 12 14
17 29 32 34 35 37
38 40 41 43 48 50
51 53 54 56 57 59
62 74 77 79 80 82
83 85 86 88
D21 D22 D20 B22 A22 A23
B23 E20 E21 B24 A24 A25
B25 C25 C26 B26 E10 A10
D10 E11 B10 A11 B11 E12
D11 D12 F12 B12 A12 E13
D13 D14 F13 B15 F14 E14
22 – 28
63 – 69
D17 D18 D16 B18 A19
B19 E16 D19 E19 E17
B20 A20 B21 A21
CCD
IMAGER
IC001
CD-573 BOARD (1/2)
13
12
60
85
CAMERA
MODULE
(1/8)
CP401
15
ı
17
53
44
48
CN001
(1/2)
CN401
(1/2)
30
34
38
16
13
ı
10
24
BUFFER
Q003
ZM SENS 1ST, 2ND
8
6
5
17
15
14
10
9
19
18
72
76
21
22
37
40
32
36
21
11
12
9
6
37
5
2
4
20
19
1
3
7
10
11
9
12
ı
15
Q001
Q002
7
4
3
ı
1
CCD OUT
POWER SAVE
V2, V4, V5A, V5B, V6
RG, H1B, H2B
V1, V3A, V3B
VHLD
VST
SHT
5
7
H1A, H2A
20
Q004 VSUB CONT
10
6
2
24
27
ı
30
16
23
25
26
21
22
8
4
19
35
33
CH-169 BOARD
CCD SIGNAL
PROCESSOR,
TIMING
GENERATOR
IC101
16 91
5 6 88
19 82
87
21
36
SHT
V4
U5
Q401
47
22
ı
35
46
45
56
42
92
39
86
80
77
97 98 100
101 103 104
105 3 2 4 7
10 14 18
89
93
J25
LENS TMP1
1
2
P21
XCAM DR PS
CN704
(1/2)
10
11
9
8
9
ı
16
25
ı
18
22
23
19
12
11
15
30
31
29
34
VVCOM
F25
P ADJ
6
29
5
VR2
J22
PANEL AD
37
35
SI, SCLK
D0 – D7
LENS IRIS
(METER)
IRIS
MOTOR
M
LENS BLOCK
TEMP OUT
ZOOM
MOTOR
M
ZOOM
SENSOR
1, 2
FOCUS
MOTOR
M
FOCUS
SENSOR
M
SHUTTER
MOTOR
LENS TEMP
SENSOR
ZOOM A, A, B, B
F RST SENS
Z RST SENS1, 2
FC SENS
IC601
G4
H4
G5
H6
21
ı
24
1
ı
4
10
ı
13
17
ı
14
18
E7
D7
F8
F7
FOCUS
MOTOR
DRIVE
ZOOM
MOTOR
DRIVE
IRIS
MOTOR
DRIVE
SHUTTER
MOTOR
DRIVE
IRIS S±, M±
FOCUS A, A, B, B
SHUTTER ±
CN601
6
A6
B5
A4
B4
C1
D2
E1
E2
8
27
(3/8)
C8
B8
C7
B7
B3
B2
A2
A1
G1
G2
H2
G3
R2
P6
N4
P4
FC EN,
FC DIR A,
FC DIR B
L4
L2
N5
G7
V LINE OUT
H26
U23
VIDEO AMP ON
SAN VOUT
VIDEO AMP
(2/8)
2
4
1
IC103
E9
B8
D9
26
25
8
9
33
32
T23
XAU LINE MUTE
Ver 1.1 2005.07
16. DSC-S60/S80/S90/ST80
A : VIDEO SIGNAL
A : AUDIO SIGNAL
A : VIDEO/AUDIO SIGNAL
USB VBUS
SY-126 BOARD (2/2)
V OUT
A OUT
XAV JACK IN
USB VBUS
SP901
SPEAKER
V OUT
CN701
SP ± SP ±
D±
6
12
14
AU OUT
4
XAV JACK IN
2
16
42
44
USB VBUS
D±
22
20
16
26
30
31
CN002
MULTI
CONNECTOR
MC-153 FLEXIBLE BOARD
AUDIO AMP
(6/8)
IC502
E6
D1
B6
05
MIC901
V LINE OUT
SAN AUOUT
SAN AUIN
XCS AUDIO
XAE LOCK LED
XSTRB LED
E5
E4
MIC SIG
CN703
2
OVERALL (1/2)
(PAGE 3-2)
MODE
DIAL
S001
(SHUTTER)
POWER
CONTROL SWITCH BLOCK
S002
8
XPWR ON XPWR ON
MODE DIAL 0, 1 L22
L25
J23
G25
K23
L23
10
XPWR LED
D001
(POWER)
USB DP, USB DM
DC/DC
CONVERTER
(7/8)
IC001
D 3.2V
ST UNREG
CAM –7.5V
PANEL 15V
EVER 2.8V
MS VCC
A 3.2V
D 1.8V
CAM 2.9V
CAM –7.5V
CAM 15V
D 1.2V
M 5V
SAN1 SO, XSAN1 SCK
F3
E3
CN702
XAV JACK IN
USB VBUS
XMS IN
SAN0 SI, SAN0 SO, XSAN0 SCK
A9
A8
X001
32.768kHz
S001 – 008,
010, 011
KEY AD 0, 1
CN706
(2/2)
A5
A2
U25
R21
V25
4
5
3
1
XAE LOCK SW
XSHTR SW
CN001
+
−
BT901
BATTERY
TERMINAL
BATT UNREG
VL 3V
BATT GND
A6
X102
12MHz
XAU LINE MUTE
F1
E22
D23
E4
F22
F9 OVERALL (1/2)
(PAGE 3-2)
1
BL L
C7
AA23
XPWR OFF
W23
XCS DD
A6
T25
Y4
MS PWR ON
D3
B10
C9
E9
A4
BL H
2
CN005
(2/2)
XACCESS LED
1
33
1
3
N21
P23
FUNCTION
KEY
D008
(MS ACCESS)
B7
K25
BATT SENS
G5
R26
XDD RST OUT
A7
B8
H1
CN704
(2/2)
13
S001
BATTERY
INSERTION
DETECT
XAF LED
XAF LED
ST-122 FLEXIBLE
BOARD (2/2)
SW-446 BOARD (2/2)
IC101
(2/2)
FRONT CONTROL
(2/8)
C6
C5
B6
AA5
AB5
Y5
BATT
TMP
X
K.BATT
INT
TH001
MS BS, MS D0 – MS D3, MS CLK
MS BS, MS D0 – MS D3, MS CLK BS, DATA0 – DATA3, SCLK
MEMORY
STICK
2
ı
5
7
8
6
6
ı
9
11
12
10
CN004 (1/2) CN002
XMS IN
11
ı
8
6
5
7
CN705
(1/2)
MS-271 BOARD (1/2)
2
CN004
(2/2)
1
15
CN705
(2/2)
16
MS-271 BOARD (2/2)
BATTERY
TEMP SENSOR
XACV IN
XACV IN
XMULTI IN
7
10
9
8
1
40
XMULTI IN
KEY AD1 C, KEY AD2 C
KEY AD1 C, KEY AD2 C
XACV IN
XMULTI IN
KEY AD1 C, KEY AD2 C
4
3
2
1
29
27
ACV UNREG
ACV
UNREG
2
4
BATT UNREG
BATT
CHG
UNREG
1
3
23
25
CRADLE ON
CRADLE ON
45 21
X K.BATT
17 14
V TH
V BATTT
18 12
5
BT001
LITHIUM
BATTERY
28
ı
34
35
ı
39
Q703
Q007,
008
D002
FLASH/
RECORDING
D001
(AE/AF LOCK)
D002
AF ILLUMINATOR
/SELF TIMER
33
31
CD-573 BOARD (2/2)
CN001
(2/2)
CN401
(2/2)
2
3
38
37
3-3 3-4
3-2. OVERALL BLOCK DIAGRAM (2/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
17. DSC-S60/S80/S90/ST80
3-5 3-6
3-3. POWER BLOCK DIAGRAM (1/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
05
SY-126 BOARD (1/2)
ST-122 FLEXIBLE BOARD
VO1-1
D 3.2V
LX2
PWR1-1
A1
UNREG1-2
K1
UNREG1-1
J1
F1
VO1-2 F2
VFB1 H2
BG4 G9
PSG4 G8
VFB4 F7
TG4 F10
C10
VFB2 D8
IC001
DC/DC
CONVERTER
(7/8)
IC002
15V/–7.5V REG
(7/8)
LDO2 A3
LX5-1 J9
LDO2IN B3
PWR2
D10
UNREG2-1
J6
UNREG2-2
K6
D 1.8V
D 1.2V
CAM 15V
CAM –7.5V
PWR1-3
C2
PWR1-2
B1
LDO3 A2
LDO3IN B2
PWR56OUT2 K7
PWR56OUT1 J7
CAM 2.9V
MS PWR IN G1
LX5-4 K10
LX5-3 K9
LX5-2 J10
UNREG
L003
L010
M 5V
F002
F001
F003
CN001
1
ı
3
12
CN704
+
−
BT901
BATTERY
TERMINAL
CAM –7.5V
BATT GND
BATT UNREG
BL H
VO3 E9
LX3 E10
BL L
VL3 F9
VO5 H10
VFB5 H9
GT6 H6
VFB6 H7
D002
D003
L005
EVER
2.8V
D001
Q002, 003
SWITCHING
Q001
Q004
SWITCHING
DC CONTROL
L008
B8 RTCBAT
H1 LDO1
SAN0 SI, SAN0 SO, XSAN0 SCK
AA23
XPWR OFF
P25
–7.5V ON
W23
XCS DD
A6
T25
V25
Y4
MS PWR ON
MS PWR ON
D3
B7
K25
BATT SENS
UNREGMON
CE
G5
R26
XDD RST OUT
A7
IC101
(1/2)
C6
C5
B6
AA5
AB5
Y5
XPWROFF
XRESET
SO
SI
SCLK
L006
3 4
7 6
REG3
REG2
1
STB
VEE
VCC
ST UNREG
ST 5V
14
D 3.2V
T001
FLASH
UNIT
L001
FLASH CONTROL,
CHARGE CONTROL
IC002
D002
AF ILLUMINATOR
/SELF TIMER
CN701
CN002
MULTI
CONNECTOR
MC-153 FLEXIBLE BOARD
S001
BATTERY
INSERTION
DETECT
BATT
TMP
X
K.BATT
TH001
MS-271 BOARD
BATTERY
TEMP SENSOR
XACV IN XACV IN
VL 3V
XACV IN
7
1
40
4
3
2
1
ACV UNREG
2
4
BATT UNREG BATT CHG UNREG
ACV UNREG
1
3
23
CRADLE ON CRADLE ON
45
21
X K.BATT
17
14
V TH
V BATTT
18
12
5
BT001
LITHIUM
BATTERY
28
ı
34
35
ı
39
Q703
Q007,
008
MS PWR
G2
MS
VCC
VCC
9
MEMORY
STICK
CN002
MS VCC
1
CN705
16
CN004
VO7 K4
PANEL 15V
2
1
15
16
POWER 2
(PAGE 3-7)
A
CAMERA
DSP,
CPU,
LENS
CONTROL,
MODE
CONTROL,
FRONT
CONTROL
(2/8)
18. DSC-S60/S80/S90/ST80
SY-126 BOARD (2/2)
M 5V
Q001, 002
DC CONTROL
B3
IC101
(2/2)
15
CN003
VDC
VDD
D 3.2V
L102
L101
SD 3.2V
D 3.2V
A 3.2V
AU 3.2V
D 1.2V
COLOR
LCD
PANEL
LCD901
PANEL UNIT
CAM 15.0V CD
CAM –7.5V
CAM 2.9V
D 3.2V
CAM 15V
CAM –7.5V CD
D 3.2V
12
13
32
39
CN401
L404
L402
FL401
L403
L002
L001
L401
FB401
FB402
CCD IMAGER
IC001
52
56
71
49
51
CCD SIGNAL
PROCESSOR,
TIMING
GENERATOR
IC101
FB201
FB202
FB403
FB001
54
55
53
57
28
27
8
1
CN001
CD-573 BOARD
CAMERA MODULE
(1/8)
CP401
CH-169 BOARD
XZM RST LED
SW-446 BOARD
32M AND FLASH
(5/8)
IC301
32M BURST
FLASH
(4/8)
IC201
128M SDRAM
(4/8)
IC203
L201
A 3.2V
L001
FL201
D002
FLASH/
RECORDING
D001
(AE/AF LOCK)
D008
(MS ACCESS)
D901
BACKLIGHT
BL H
CN004
6
5
2
1
17
BL L
BL H
4
CN005
CN706
BL L
2
30
30
4
PANEL 15V
32
2
32
CONTROL SWITCH BLOCK
A 3.2V
A 3.2V
A 3.2V
9
2
CN702
D001
(POWER)
AUDIO AMP
(6/8)
IC502
2.8V REG
(6/8)
IC503
1
4
A 3.2V
VOUT
VDD
A 3.2V
M 5V
CN601
F RST VCC
Q601
ZOOM
SENSOR
LENS BLOCK
FOCUS
SENSOR
20
25
Z RST VCC1
Z RST VCC2
ZOOM
SENSOR
1, 2
9
XZM RST LED
D 3.2V
IC601
LENS DRIVE
(3/8)
L104
VI 3.2V
VIDEO AMP
(2/8)
IC103
D 3.2V D 3.2V
D 1.8V
D 1.2V
CAM 15V
CAM –7.5V
CAM 2.9V
M 5V
BL H
BL L
PANEL 15V
POWER 2
(PAGE 3-6) A
05
CAMERA
DSP,
CPU,
LENS
CONTROL,
MODE
CONTROL,
FRONT
CONTROL
(2/8)
3-7 3-8E
3-4. POWER BLOCK DIAGRAM (2/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
Ver 1.1 2005.07
20. DSC-S60/S80/S90/ST80
Link
Link
4-2. SCHEMATIC DIAGRAMS
MC-153 FLEXIBLE BOARD
(MULTI CONNECTOR)
SW-446 BOARD
(CONTROL SWITCH, LCD PANEL)
ST-122 FLEXIBLE BOARD (FLASH DRIVE) CONTROL SWITCH BLOCK
MS-271 BOARD (MEMORY STICK CONNECTOR)
CD-573 BOARD (CCD IMAGER)
MC-153 FLEXIBLE BOARD
(MULTI CONNECTOR)
SW-446 BOARD
(CONTROL SWITCH, LCD PANEL)
ST-122 FLEXIBLE BOARD (FLASH DRIVE) CONTROL SWITCH BLOCK
MS-271 BOARD (MEMORY STICK CONNECTOR)
CD-573 BOARD (CCD IMAGER)
COMMON NOTE FOR SCHEMATIC DIAGRAMS
COMMON NOTE FOR SCHEMATIC DIAGRAMS
21. 4-5
DSC-S60/S80/S90/ST80
4-2. SCHEMATIC DIAGRAMS
4-2. SCHEMATIC DIAGRAMS
1. Connection
2. Adjust the distance so that the output waveform of
Fig. a and the Fig. b can be obtain.
When indicating parts by reference number, please
include the board name.
4-2. SCHEMATIC DIAGRAMS
(For schematic diagrams)
• All capacitors are in µF unless otherwise noted. pF : µ
µF. 50V or less are not indicated except for electrolytics
and tantalums.
• Chip resistors are 1/10 W unless otherwise noted.
kΩ=1000 Ω, MΩ=1000 kΩ.
• Caution when replacing chip parts.
New parts must be attached after removal of chip.
Be careful not to heat the minus side of tantalum
capacitor, Because it is damaged by the heat.
• Some chip part will be indicated as follows.
Example C541 L452
22U 10UH
TA A 2520
• Constants of resistors, capacitors, ICs and etc with XX
indicate that they are not used.
In such cases, the unused circuits may be indicated.
• Parts with ★ differ according to the model/destination.
Refer to the mount table for each function.
• All variable and adjustable resistors have characteristic
curve B, unless otherwise noted.
• Signal name
XEDIT → EDIT PB/XREC → PB/REC
• 2: non flammable resistor
• 5: fusible resistor
• C: panel designation
• A: B+ Line
• B: B– Line
• J : IN/OUT direction of (+,–) B LINE.
• C: adjustment for repair.
• A: not use circuit
• Circled numbers refer to waveforms.
(Measuring conditions voltage and waveform)
• Voltages and waveforms are measured between the
measurement points and ground when camera shoots
color bar chart of pattern box.They are reference values
and reference waveforms.
(VOM of DC 10 MΩ input impedance is used)
• Voltage values change depending upon input
impedance of VOM used.)
Kinds of capacitor
Case size
External dimensions (mm)
Yellow
A A
B B
A=B
Fig. a (Video output terminal output waveform)
H
Cyan
Green
White
Magenta
Red
Blue
Fig.b (Picture on monitor TV)
CRT picture frame
Electronic beam
scanning frame
THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS
(In addition to this, the necessary note is printed in each block)
Front of the lens
L = About 29 cm(PTB-450)
L = About 12 cm(PTB-1450)
L
Pattern box
Pattern box Color bar chart
Pattern box PTB-450
J-6082-200-A
or
Small pattern box
PTB-1450
J-6082-557-A
For PTB-450:
J-6020-250-A
For PTB-1450:
J-6082-559-A
Precautions for Replacement of CCD Imager
• The CD-573 board mounted as a repair part is not equipped
with a CCD imager.
When replacing this board, remove the CCD imager from
the old one and mount it onto the new one.
• If the CCD imager has been replaced, carry out all the
adjustments for the camera section.
• As the CCD imager may be damaged by static electricity
from its structure, handle it carefully like for the MOS IC.
In addition, ensure that the receiver is not covered with
dusts nor exposed to strong light.
The components identified by mark 0 or dotted line with
mark 0 are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque 0 sont
critiques pour la sécurité.
Ne les remplacer que par une pièce portant le numéro
spécifie.
22. DSC-S60/S80/S90/ST80
16V
XX
C004
XX
C005
16V
XX
C009
Note: IC001 is not supplied, but this is
included in CCD block assy.
Note: Voltage and Waveform of mounted IC001 and
Q001 to Q004 on CD-573 board can not be measured,
because they are mounted by the side of the lens.
39P
CN001
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
SML-310YTT86
D002
SML-510MWT86
D001
DTC144EMT2L
Q002
16V
0.1u
C003
DTC144EMT2L
Q004
3900
R005
16V
0.1u
C001
2200
R003
0
R001
FB001
0.1u
16V
C007
3300
R004
22k
R002
16V
0.1u
C008
DTC144EMT2L
Q001
1300
R006
2SC39320S2S0
Q003
ICX488DQF-13
IC001
1
V
6
2
V
5B
3
V
5A
4
V
4
5
V
3B
6
V
3A
7
V
2
8
V
1
9
V
ST
10
V
HOLD
11
GND
12
GND
13
V
OUT
14
VDD
15
RG
16
H
1B
17
H
2B
18
GND
19
SUB
20
C
sub
21
H
1A
22
H
2A
23
GND
24
VL
16V
0.1u
C006
56
R007
1
A
VST
GND
SHT
V5B
H2A
RG
H2B
GND
V3B
GND
GND
V2
D_3.2V
GND
XSTRB_LED
V5A
V1
GND
CCD_OUT
H1B
GND
VHLD
GND
H1A
GND
CAM_-7.5V_CD
CAM_15.0V_CD
VSUB_CONT
CAM_15.0V_CD
GND
GND
V6
XAE_LOCK_LED
GND
POWER_SAVE
GND
V4
GND
V3A
THROUGH THE
PAGE 4-11
SY-126
(1/8)
FP-201 FLEXIBLE
of LEVEL3
CN401
FLASH
/RECORDING
(AE/AF LOCK)
SWITCH
SWITCH
BUFFER
SWITCH
IC001
CCD IMAGER
D
F
B
XX MARK:NO MOUNT
E
5
3
CD-573 BOARD
C
6
2 9
7
G
4
CCD IMAGER
05
8
4-7 4-8 CD-573
For Schematic Diagram
• Refer to page 4-37 for printed wiring board.
25. DSC-S60/S80/S90/ST80
For Schematic Diagram
• Refer to page 4-43 for printed wiring board.
4-29 4-30 ST-122
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque 0 sont
critiques pour la sécurité. Ne les remplacer que
par une piéce portant le numéro spécifié.
0
269
NO MARK:REC/PB MODE
0 0
4.2
5
0
4.2
0
3.2
T001
4
1
2 3
5
4.7M
R002
0.047u
250V
C004
1u
C002
33
R003
±0.5%
CY25BAJ-8F-T23
Q001
1M
R004
2.2uH
L001
LND018
XE_K(L)
LND017
XE_A(H)
LND019
TRIGGER
D001
CRF02(TE85R)
L002
6.3V
22u
C001
LND007 ST_GND
LND008 STRB_ON
LND013 XAF_LED
LND009 STRB_CHG_CONT
LND014 D_3.2V
LND012 ST_5V
LND010 XSTRB_FULL
LND002 ST_UNREG
LND003 ST_UNREG
LND011 STRB_CHG
LND004 ST_GND
LND001 ST_UNREG
LND005 ST_GND
LND006 ST_GND
315V
135u
C003
IC002
TPS65552RGTR
SW
1
SW
2
VCC
3
F_ON
4
NC
5
I_PEAK
6
G_IGBT
7
NC
8
XFULL
9
CHG
10
PGND
11
PGND
12
NC
13
NC
14
VBATT
15
NC
16
HGND
17
0.1u
C006
1
A
10
8
11
2
7
12
6
4
3
14
9
13
5
1
FLASH CONTROL,
IC002
CHARGE CONTROL
FLASH DRIVE
FLASH
UNIT CHARGING
CAPACITOR
(7/8)
of LEVEL3
CN704
PAGE 4-23
SY-126
1
2
3
E
5
3
XX MARK:NO MOUNT
C
6
2 9
7
4 10
05
8
ST-122 FLEXIBLE BOARD
FLASH DRIVE
D
B
OPY5252
D002
/SELF TIMER
AF ILLUMINATOR
26. DSC-S60/S80/S90/ST80
Note: CN002 (MULTI CONNECTOR) is not supplied,
but this is included in MC-153 flexible
complete board.
LND038
VMZ6.8NT2L
D003
3
2
1
LND029
LND022
LND027
LND044
LND045
LND003
LND046
SP+
BT001
VMZ6.8NT2L
D002
3
2
1
470
R006
LND048
LND037
LND019
LND012
LND009
D001
MAZS068008SO
LND035
LND033
LND013
LND016
LND020
145658321
LF001
1 3
4
2
LND028
LND041
LND011
LND006
LND031
LND010
LND039
LND002
LND007
LND005
LND047
SP-
LND040
LND023
LND017
LND001
LND018
LND032
LND034
LND004
LND024
LND026
LND014
LND008
LND015
LND036
LND042
LND025
LND043
LND021
CN002
32P
LND030
FB001
FB002
0
R003
1
A
ACV_UNREG
TO AV/USB MULTI CABLE OR CRADLE
X_CGH_ON
ACV_UNREG
ACV_UNREG
ACV_GND
ACV_GND
STATIC_GND
ACV_UNREG
ACV_GND
ACV_GND
XACV_IN
SP-
D-
V_OUT
ACV_GND
XAV_JACK_IN
USB_VBUS
A_OUT
BATT_UNREG
A_GND
KEY_AD1_C
ACV_UNREG
BATT_UNREG
D+
NC(UART_SO)
BATT_UNREG
XMULTI_IN
X_K.BATT
A_GND
CRADLE_ON
CRADLE_ON
USB_GND
KEY_AD1_C
ACV_GND
V_BATT
X_K.BATT
ACV_GND
BATT_UNREG
VL_3V
V_OUT
NC
ACV_UNREG
USB_VBUS
XACV_IN
ACV_GND
ACV_GND
USB_GND
ACV_GND
X_CGH_ON
XCAM_IN
XMULTI_IN
V_GND
V_TH
AU_OUT
D-
NC
SP+
V_GND
V_TH
NC(UART_SI)
USB_GND
KEY_AD2_C
ACV_UNREG
XAV_JACK_IN
V_BATT
KEY_AD2_C
ACV_UNREG
ACV_GND
BATT_UNREG
D+
NC(XPWR_ON_P)
ACV_UNREG
ACV_GND
BATT_UNREG
USB_GND
NC
BATT_UNREG
N.C.
28
20
22
24
26
30
32
16
8
12
6
18
10
14
2
4
5
7
9
29
15
3
21
25
19
11
17
13
31
1
23
27
16
9
8
21
10
20
22
13
14
33
37
41
15
12
19
25
35
39
36
23
43
28
42
29
4
45
44
24
40
32
17
7
1
26
11
30
6
27
3
38
2
18
34
5
31
BATTERY
LITHIUM
SPEAKER
SP901
PAGE 4-25
CN701
SY-126
(8/8)
of LEVEL3
(MULTI CONNECTOR)
E
5
3
XX MARK:NO MOUNT
C
6
2 9
7
G
4 10
05
8
MC-153 FLEXIBLE BOARD
MULTI CONNECTOR
D
F
B
For Schematic Diagram
• Refer to page 4-43 for printed wiring board.
4-31 4-32 MC-153
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque 0 sont
critiques pour la sécurité. Ne les remplacer que
par une piéce portant le numéro spécifié.
27. DSC-S60/S80/S90/ST80
For Schematic Diagram
• Refer to page 4-45 for printed wiring board.
4-33 4-34 MS-271, CONTROL SWITCH BLOCK
CN002 10P
1 VSS
2 BS
3 DATA1
4 SDIO/DATA0
5 DATA2
6 INT
7 DATA3
8 SCLK
9 VCC
10 VSS
TH001
S001
1
2
3
4
1k
R004
16P
CN004
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
FB003
FB001
FB004
FB002
1
A
MS_BS
XMS_IN
MS_D1
MS_CLK
MS_D3
REG_GND
MS_D0
MS_D2
REG_GND
BATT_TMP
X_K.BATT
REG_GND
REG_GND
MS_VCC
STATIC_GND
REG_GND
REG_GND
11
12
BATTERY
INSERTION DETECT
STICK
MEMORY
MEMORY
STICK
MEMORY STICK CONNECTOR
05
4
3
MS-271 BOARD
XX MARK:NO MOUNT
C
2
B
4
3
THROUGH THE
FP-199 FLEXIBLE
SY-126
PAGE 4-25
(8/8)
of LEVEL3
CN705
CONTROL SWITCH BLOCK is replaced as block,
so that PRINTED WIRING BOARD is omitted.
R010
4000
LND006
LND007
R006
4000
LND009
R007
4000
LND002
R011
4000
R016
6400
S002
1
2
3
4
LND010
R012
4000
LND003
R009
4000
LND004
LND001
D001
S001
LND005
LND008
R008
4000
R017
4000
4000
R018
R015
6400
R013
4000
1
A
6
7
XSHTR_SW
(2nd)
4
REG_GND
(1st)
XPWR_LED
5
MODE_DIAL0
9
A_3.2V
1
2
3
N.C.
XAE_LOCK_SW
8
10
XPWR_ON
MODE_DIAL1
A_3.2V
Landscape
portrait Twilight
Candle
PLAY
MOVIE
Snow
Soft
+
snap
P_AUTO
Beach
AUTO
AUTO M
PLAY
P_AUTO
MOVIE
Twilight
Beach
Snow
Candle
Twilight
portrait
+
Twilight
M
snap
Soft
Landscape
(POWER)
POWER
(SHUTTER)
PAGE 4-23
(7/8)
CN702
SY-126
of LEVEL3
D
F
B
E
5
3
CONTROL SWITCH BLOCK
C
2 4
05
XX MARK:NO MOUNT
28. DSC-S60/S80/S90/ST80
Link
Link
4-3. PRINTED WIRING BOARDS
MC-153 FLEXIBLE BOARD
ST-122 FLEXIBLE BOARD
SW-446 BOARD MS-271 BOARD
CD-573 BOARD MC-153 FLEXIBLE BOARD
ST-122 FLEXIBLE BOARD
SW-446 BOARD MS-271 BOARD
CD-573 BOARD
CIRCUIT BOARDS LOCATION
COMMON NOTE FOR PRINTED WIRING BOARDS
MOUNTED PARTS LOCATION CIRCUIT BOARDS LOCATION
COMMON NOTE FOR PRINTED WIRING BOARDS
MOUNTED PARTS LOCATION
Board Name Function
CD-573 CCD IMAGER
SW-446 CONTROL SWITCH, LCD PANEL
ST-122 FLEXIBLE FLASH DRIVE
MC-153 FLEXIBLE MULTI CONNECTOR
MS-271 MEMORY STICK CONNECTOR
29. 4-35
DSC-S60/S80/S90/ST80
4-3. PRINTED WIRING BOARDS
4-3. PRINTED WIRING BOARDS
• : Uses unleaded solder.
• : Circuit board
: Flexible board
Pattern from the side which enables seeing.
: pattern of the rear side
(The other layers’ patterns are not indicated)
• Through hole is omitted.
• Circled numbers refer to waveforms.
• There are a few cases that the part printed on diagram
isn’t mounted in this model.
• C: panel designation
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS
2 1
3
2 1
3
2 1
3
3
4
5
2
1
1
2
3
6
5
4
E
B
C
3
1
5
2
4
6
1
2
3
6
5
4
3
1
5
2
4
6
1
2
3
5
4
4 3
1 2
3
1 2
4
5
5
3 4
1
2
1
4
2
3
4
6
2
5
3
1
1
2
4
3
1
4
2
3
• Chip parts.
Transistor Diode
4-3. PRINTED WIRING BOARDS
Board Name
Parts Location Pattern
(Shown on Page) Total Number of Layers Layers Not Indicated
CD-573 4-50 4 layers 2 and 3 layers
SW-446 4-52 4 layers 2 and 3 layers
ST-122 flexible 4-52 2 layers –
MC-153 flexible – 2 layers –
MS-271 – 2 layers –
30. DSC-S60/S80/S90/ST80
4-38
CD-573
Note for Printed Wiring Board (See page 4-35).
: Uses unleaded solder.
CD-573
4-37
2
38
1
39
B
+
C
B
E
C
B
E
CN001
C001
C003
C004
C005
C006
C007
C008
C009
IC001
Q001
Q002
Q003
Q004
FB001
R001
R002
R003
R004
R005
R006
R007
24
13
12 1
E
B
B
E
C
C
1 2 3
05
CD-573 BOARD (SIDE A)
1-866-280-
Note: IC001 is not supplied, but this is
included in CCD block assy.
11 21
C
D
B
A
A
K
A
K
D001
D002
D001
(AE/AF LOCK)
D002
FLASH/
RECORDING
1
2
3
05
CD-573 BOARD (SIDE B)
1-866-280- 11 21
C
D
B
A
39. NOTE
NOTE
DSC-S60/S80/S90/ST80
Link
Link
5. REPAIR PARTS LIST
Link
Link ELECTRICAL PARTS LIST
ELECTRICAL PARTS LIST
EXPLODED VIEWS
EXPLODED VIEWS
ACCESSORIES
ACCESSORIES
NOTE: Characters A to Z of the electrical parts list indicate location of exploded views in which the desired part is shown.
CABINET SECTION
CABINET SECTION MAIN BLOCK ASSEMBLY
MAIN BLOCK ASSEMBLY LENS BLOCK ASSEMBLY
LENS BLOCK ASSEMBLY
A B C
MS-271 BOARD
ST-122 FLEXIBLE BOARD
SW-446 BOARD
CD-573 BOARD
MC-153 FLEXIBLE BOARD
MS-271 BOARD
ST-122 FLEXIBLE BOARD
SW-446 BOARD
CD-573 BOARD
MC-153 FLEXIBLE BOARD
C
B
B
B
B
40. 5. REPAIR PARTS LIST
5-1
5. REPAIR PARTS LIST
5. REPAIR PARTS LIST
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque
0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifié.
NOTE:
• -XX, -X mean standardized parts, so they may have some differences from
the original one.
• Items marked “*” are not stocked since they are seldom required for routine
service. Some delay should be anticipated when ordering these items.
• The mechanical parts with no reference number in the exploded views are not
supplied.
• Due to standardization, replacements in the parts list may be different from
the parts specified in the diagrams or the components used on the set.
• CAPACITORS:
uF: µF
• COILS
uH: µH
• RESISTORS
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F: nonflammable
• SEMICONDUCTORS
In each case, u: µ, for example:
uA...: µA... , uPA... , µPA... ,
uPB... , µPB... , µPC... , µPC... ,
uPD..., µPD...
• Abbreviation
AR : Argentine model
AUS : Australian model
CH : Chinese model
CND : Canadian model
HK : Hong Kong model
JE : Tourist model
KR : Korean model
DSC-S60/S80/S90/ST80
• Language that can be selected about SY-126 board
When indicating parts by reference number,
please include the board name.
Area
Japanese
English
French
German
Spanish
Italian
Portugal
Simplified
Chinese
Traditional
Chinese
Arabic
Dutch
Russian
Swedish
Korean
GP1 J z z
US
GP2
CND
z z z z z z
AUS
Vietnam
GP3
AEP
z z z z z z z z z
UK
E
GP4
AR
z z z z z z
BR
TW
JE
GP5
HK
z z z z z z
CH
KR
47. 5-12
DSC-S60/S80/S90/ST80
Checking supplied accessories.
The components identified by
mark 0 or dotted line with
mark 0 are critical for safety.
Replace only with part num-
ber specified.
Les composants identifiés par une
marque 0 sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
Battery case (1)
3-074-757-01
Battery charger
(BC-CS2A/CS2B) (1)
0 1-477-814-51 (AEP, UK, E, AR, HK, AUS)
0 1-477-814-61 (KR, CH)
0 1-477-814-41 (US, CND, JE)
Power cord (1)
0 1-827-269-12 (UK, HK)
0 1-575-131-82 (AEP, E)
AC Adaptor
AC-LS5 (1)
0 1-479-284-51
Power cord (1)
0 1-776-985-12 (KR)
0 1-782-476-51 (CH)
0 1-827-269-12 (UK, HK)
0 1-783-952-21 (AR)
0 1-790-107-42 (US, CND)
0 1-790-732-12 (JE)
0 1-575-131-82 (AEP, E)
0 1-555-074-52 (AUS)
DSC-S60 only
HR6 (size AA) Nickel-Metal
Hydride batteries (2)
(Note)
Rechargeable battery pack
(NP-NH25) (1)
(Note)
R6 (size AA) alkaline
batteries (2)
(Note)
USB, AV cable for
multi-use terminal (1)
1-830-345-11
USB, AV cable for
multi-use terminal (1)
1-830-345-11
Conversion 2P adaptor (1)
0 1-569-007-12 (JE)
Conversion 2P adaptor (1)
0 1-569-008-21 (E)
USB cable (1)
1-827-754-11
A/V connecting cable (1)
0 1-824-519-11
Cyber-shot Station
(CSS-SA) (1)
1-819-202-11
Conversion 2P adaptor (1)
0 1-569-008-21 (E)
DSC-S80/S90 only
DSC-ST80 only
Other accessories
2-590-046-11 MANUAL, INSTRUCTION (CSS-SA)
(ENGLISH, FRENCH) (AEP, UK, E, HK)
2-590-046-21 MANUAL, INSTRUCTION (CSS-SA)
(GERMAN, ITALIAN, DUTCH, SPANISH,
PORTUGUESE, SWEDISH, DANISH,
FINNISH, RUSSIAN) (AEP, E)
2-590-046-31 MANUAL, INSTRUCTION (CSS-SA)
(TRADITIONAL CHINESE, SIMPLIFIED
CHINESE, KOREAN, ARABIC) (E, HK)
Ver. 1.4 2007.10
The changed portions from
Ver. 1.3 are shown in blue.
Note: This item is supplied with the unit as an accessory,
but is not prepared as a service part.
51. — 2 —
DSC-S60/S80/S90/ST80_L2
2-5. ZOOM MOTOR UNIT REPLACEMENT AND INSPECTION PROCEDURES
Service parts
Part Number Part Name Quantity
1 2-891-376-01 MOTOR UINT, ZOOM 1
Note: These parts are not prepared as service parts.
Recycle removed screws.
1 Remove solder of “Zoom motor terminal” (4 point).
*Be careful for terminal deformation and breaking of coil.
2 Remove two screws that fix “Motor Unit, Zoom”.
*Removed screws are recycled. Do not lose them.
*Lens barrel should not be pulled out.
*Do not touch the motor directly for preventing rust. (Use finger cot etc...)
*Be careful not to damage the appearance.
3 Confirming Zoom function manually.
3-1. Turn Lens gear to clockwise and poke put the lens barrel until the position of open lens barrier.
3-2. Turn to the lens barrel (outside) for TELE end and WIDE end for four or five times and then confirm no against force during stroke.
3-3. During the lens barrel stroke check, confirm the condition of lens gear if there is no deformation of damage.
3-4. If everything is OK, step forward to next.
*If found any problem until this point, it is impossible to repair ZOOM motor unit. Therefore, replace the lens block assembly.
2. DISASSEMBLY
1
not supplied (Note)
Zoom Motor Unit
Two Screws Solder
Rotate lens barrel and stroke
Length of gear
All circumferences
52. — 3 —
DSC-S60/S80/S90/ST80_L2
4 Throw in each gear of the new Motor Unit, Zoom, and fix with two screws.
*Lens barrel should not be pulled out.
*Do not touch the motor directly for preventing rust. (Use finger cot etc...)
*Be careful not to damage the appearance.
5 Solder of “Zoom motor terminal” (4 point).
*Be careful for terminal deformation and breaking of coil.
6 Assemble lens to the unit.
7 Execute the necessary adjustment items referring to Service Manual, ADJ.
8 Final inspection
8-1. Zoom function
*Confirm five position. (refer to the picture)
*Make sure if there is no mechanical noise and illegal motion when zooming (From TELE end to WIDE end).
8-2. Zooming picture
*Make sure if there is no missing frame or unstable pictures in LCD or EVF.
8-3. Barrier
*Confirm five position. (refer to the picture)
*Make sure if it moves smoothly without any interference, and does not have abnormal sound.
8-4. Appearance
*Make sure if there is no scratch or dirt on the surface unless customers permit.
8-5. Dust on lens
*Make sure if there is no dust in the lens.
Zoom Motor Unit
Two Screws Solder
Lens stored
Lens at TELE end
Upward
Downward
Horizontal
Upper oblique 45˚
Lower oblique 45˚
Full stroke check
53. — 4 —
DSC-S60/S80/S90/ST80_L2
4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
4-2. SCHEMATIC DIAGRAMS
MC-153 FLEXIBLE BOARD (MULTI CONNECTOR)
(Service manual page 4-31, Location A-3 to F-5)
• Change of Repair Parts
: Points changed portion.
Former New
VMZ6.8NT2L
D003
3
2
1
VMZ6.8NT2L
D002
3
2
1
D001
MAZS068008SO
0
R003
XX
D003
3
2
1
XX
D002
3
2
1
D001
XX
0
R003
54. — 5 —
DSC-S60/S80/S90/ST80_L2
5-1. EXPLODED VIEWS
Page Former New
Ref. No. Part No. Description Ref. No. Part No. Description
5-3
3 2-025-236-31 SCREW (M1.7)
60 2-025-236-31 SCREW (M1.7)
SP901 1-825-665-11 SPEAKER (1.3CM) (Note 2)
3 2-599-475-31 SCREW (M1.7)
60 2-599-475-31 SCREW (M1.7)
SP901 1-825-923-11 LOUDSPEAKER (1.3CM) (Note 2)
5. REPAIR PARTS LIST
& : Points added portion.
5-2
101
102
(Note 1)
103
(Note 1)
104
(Note 1)
114
(Note 1)
101
102
(Note 1)
103
(Note 1)
104
(Note 1)
114
(Note 1)
115
(Note 4)
ns
+
(
115 2-891-376-01 MOTOR UNIT, ZOOM
ns: not supplied
Note 4: Be sure to read “2-5. ZOOM MOTOR
UNIT REPLACEMENT AND INSPEC-
TION PROCEDURES” on page 2 when
change Ref. No. 115.
5-4
55. — 6 —
DSC-S60/S80/S90/ST80_L2
Page Former New
Ref. No. Part No. Description Ref. No. Part No. Description
A-1106-343-A CD-573 BOARD, COMPLETE
***********************
< CONNECTOR >
CN001 1-817-942-11 CONNECTOR, FPC (ZIF) 39P
< DIODE >
D001 8-719-063-83 DIODE SML-510MWT86 (AE/AF LOCK)
A-1106-346-A MC-153 FLEXIBLE BOARD, COMPLETE
*******************************
SP901 1-825-665-11 SPEAKER (1.3CM)
< DIODE >
D001 8-719-056-54 DIODE MAZS068008SO
D002 6-500-776-01 DIODE MAZW068H0LS0
D003 6-500-776-01 DIODE MAZW068H0LS0
A-1106-341-A MS-271 BOARD, COMPLETE
***********************
< CONNECTOR >
CN002 1-815-572-61 CONNECTOR, MEMORY STICK
CN004 1-816-646-31 FFC/FPC CONNECTOR (LIF) 16P
0 A-1106-345-A ST-122 FLEXIBLE BOARD, COMPLETE
*******************************
< CAPACITOR >
C002 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V
A-1106-342-A SW-446 BOARD, COMPLETE
***********************
< CONNECTOR >
CN003 1-784-423-21 FFC/CONNECTOR, FPC (ZIF) 39P
CN004 1-816-654-31 FFC/FPC CONNECTOR (LIF) 6P
CN005 1-815-333-11 CONNECTOR, FPC (ZIF) 33P
A-1106-343-A CD-573 BOARD, COMPLETE
***********************
< CONNECTOR >
* CN001 1-817-942-51 CONNECTOR, FPC (ZIF) 39P
< DIODE >
D001 8-719-075-29 DIODE SML-510MWT86S (AE/AF LOCK)
A-1106-346-A MC-153 FLEXIBLE BOARD, COMPLETE
*******************************
SP901 1-825-923-11 LOUDSPEAKER (1.3CM)
< DIODE >
A-1106-341-A MS-271 BOARD, COMPLETE
***********************
< CONNECTOR >
CN002 1-815-572-71 CONNECTOR, MEMORY STICK
* CN004 1-816-646-51 FFC/FPC CONNECTOR (LIF) 16P
0 A-1106-345-A ST-122 FLEXIBLE BOARD, COMPLETE
*******************************
< CAPACITOR >
C002 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
A-1106-342-A SW-446 BOARD, COMPLETE
***********************
< CONNECTOR >
* CN003 1-793-300-51 CONNECTOR, FPC (ZIF) 39P
* CN004 1-816-654-51 FFC/FPC CONNECTOR (LIF) 6P
* CN005 1-815-333-51 CONNECTOR, FPC (ZIF) 33P
5-5
5-2. ELECTRICAL PARTS LIST
5-7
The components identified by
mark 0 or dotted line with
mark 0 are critical for safety.
Replace only with part num-
ber specified.
Les composants identifiés par une
marque 0 sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
5-7
5-7
5-7
56. [Description of main button functions on toolbar of the Adobe Acrobat Reader Ver5.0 (for Windows)]
Printing a text
1. Click the Print button .
2. Specify a printer, print range, number of copies, and other op-
tions, and then click [OK].
Application of printing:
To set a range to be printed within a page, select the graphic
selection tool and drag on the page to enclose a range to
be printed, and then click the Print button.
Finding a text
1. Click the Find button .
2. Enter a character string to be found into a text box, and click
the [Find]. (Specify the find options as necessary)
Application to the Service Manual:
To execute “find” from current page toward the previous pages,
select the check box “Find Backward” and then click the
“Find”.
3. Open the find dialog box again, and click the [FindAgain] and
you can find the matched character strings displayed next.
(Character strings entered previously are displayed as they are
in the text box.)
Application to the Service Manual:
The parts on the drawing pages (block diagrams, circuit dia-
grams, printed circuit boards) and parts list pages in a text
can be found using this find function. For example, find a
Ref. No. of IC on the block diagram, and click the [FindAgain]
continuously, so that you can move to the Ref. No. of IC on
the circuit diagram or printed circuit board diagram succes-
sively.
Note: The find function may not be applied to the Service
Manual depending on the date of issue.
Switching a page
• To move to the first page, click the .
• To move to the last page, click the .
• To move to the previous page, click the .
• To move to the next page, click the .
Reversing the screens displayed once
• To reverse the previous screens (operation) one by one, click
the .
• To advance the reversed screens (operation) one by one, click
the .
Application to the Service Manual:
This function allows you to go and back between circuit dia-
gram and printed circuit board diagram, and accordingly it
will be convenient for the voltage check.
Moving with link
1. Select either palm tool , zoom tool , text selection tool
, or graphic selection tool .
2. Place the pointer in the position in a text where the link exists
(such as a button on cover and the table of contents page, or
blue characters on the removal flowchart page or drawing
page), and the pointer will change to the forefinger form .
3. Then, click the link. (You will go to the link destination.)
Moving with bookmark:
Click an item (text) on the bookmark pallet, and you can move
to the link destination. Also, clicking can display the
hidden items.
(To go back to original state, click )
Zooming or rotating the screen display
“Zoom in/out”
• Click the triangle button in the zoom control box to select the
display magnification. Or, you may click or for zoom-
ing in or out.
“Rotate”
• Click rotate tool , and the page then rotates 90 degrees each.
Application to the Service Manual:
The printed circuit board diagram you see now can be changed
to the same direction as the set.
Toolbar
57. Revision History
Reverse
DSC-S60/S80/S90/ST80
Ver.
1.0
1.1
1.2
1.3
1.4
Date
2005.03
2005.07
2005.07
2006.09
2007.10
History
Official Release
Correction-1
(C1)
Supplement-1
(S1 PV05-033)
Correction-2
(C2)
Supplement-2
(S2 DI07-158)
Contents
—
• Deletion of LCD Type (TYPE S)
S.M. correction: Cover, Page 3, Page 4,
Page 1-4, Page 3-2,
Page 3-7, Page 4-2,
Page 4-27, Page 5-3,
Page 5-7, Page 5-8
• Correction of Overall Block Diagram
S.M. correction: Page 3-1
• Correction of Repair Parts
S.M. correction: Page 5-4, Page 5-12
• Precaution on Replacing the SY-126 Board
• Correction of Repair Parts
S.M. correction: Page 5-2, Page 5-4
• Addition of “2-5. ZOOM MOTOR UNIT
REPLACEMENT AND INSPECTION
PROCEDURES”
• Change of Repair Parts
• Revision of Accessories
S.M. revised: Page 5-12, Page 5-13
S.M. Rev.
issued
—
Yes
No
Yes
Yes
987686935.pdf
![— 2 —
DSC-S60/S80/S90/ST80
Camera
[System]
Image device 6.85 mm (1/2.7 type) color
CCD, Primary color filter
Total pixel number of camera
Approx. 4 231 000 pixels
Effective pixel number of camera
Approx. 4 065 000 pixels
Lens Carl Zeiss Vario-Tessar
3× zoom lens
f = 6.0 - 18.0 mm (39 - 117 mm
when converted to a 35 mm still
camera)
F2.8 - 5.2
Exposure control Automatic exposure, Manual
exposure, Scene Selection (7
modes)
White balance Automatic, Daylight, Cloudy,
Fluorescent, Incandescent
File format (DCF compliant)
Still images: Exif Ver. 2.2
JPEG compliant, DPOF
compatible
Movies: MPEG1 compliant
(Monaural)
Recording media Internal memory 32 MB
“Memory Stick”
Flash Recommended distance (ISO
set to Auto): 0.2 m to 4.5 m
(7 7/8 inches to 178 1/2 inches)
(W)/0.5 m to 2.5 m
(19 3/4 inches to 98 1/2 inches)
(T)
[Input and Output connectors]
Multi connector
USB communication
Hi-Speed USB (USB 2.0
compliant)
[LCD screen]
LCD panel DSC-S90:
6.2 cm (2.5 type) TFT drive
DSC-S80/ST80/S60:
5.1 cm (2.0 type) TFT drive
Total number of dots
115 200 (480×240) dots
[Power, general]
Power HR15/51:HR6 (Size AA)
Nickel-Metal Hydride batteries
(2) (supplied with DSC-S90/
S80), 2.4 V
R6 (size AA) Alkaline batteries
(2) (supplied with DSC-S60),
3 V
Battery pack NP-NH25 (1)
(supplied with DSC-ST80)
ZR6 (size AA) Oxy Nickel
Primary Battery (2) (not
supplied), 3 V
AC-LS5K AC Adaptor (not
supplied), 4.2 V
Power consumption
(during shooting with the LCD screen on)
DSC-S90: 1.1 W
DSC-S80/ST80/S60: 1.0 W
Operating temperature
0°C to +40°C (+32°F to
+104°F)
Storage temperature
–20°C to +60°C (–4°F to
+140°F)
Dimensions 96.6×64.4×40.1 mm
(3 7/8×2 5/8×1 5/8 inches)
(W/H/D, excluding maximum
protrusions)
Mass DSC-S90:
Approx. 253 g (8 oz) (including
two batterries and wrist strap)
DSC-S80/ST80/S60:
Approx. 249 g (8 oz) (including
two batterries and wrist strap)
Microphone Electret condenser microphone
Speaker Dynamic speaker
Exif Print Compatible
PRINT Image Matching III
Compatible
PictBridge Compatible
SPECIFICATIONS
BC-CS2A/CS2B Ni-MH battery charger
(supplied with DSC-S90/S80)
Power requirements
AC 100 to 240 V, 50/60 Hz,
3 W
Output voltage AA: DC 1.4V 400 mA × 2
AAA: DC 1.4 V 160 mA × 2
Operating temperature
0°C to +40°C (+32°F to
+104°F)
Storage temperature
–20°C to +60°C (–4°F to
+140°F)
Dimensions Approx. 71×30×91 mm
(2 7/8×1 3/16×3 5/8 inches)
(W/H/D)
Mass Approx. 90 g (3 oz)
Design and specifications are subject to change
without notice.
(supplied with DSC-ST80)
(supplied with DSC-ST80)
Cyber-shot Station CSS-SA
[Input/Output connectors]
A/V OUT (MONO) jack (Monaural)
Minijack
Video*: 1 Vp-p, 75 Ω, unbalanced,
sync negative
Audio*: 327 mV (47 kΩ loaded)
Output impedance: 2.2 kΩ
* When the DSC-S90/S80/ST80/S60 is
connected.
USB jack: B
DC IN jack
Multi connector
[General]
Dimensions (Approx.):
120 × 36 × 89 mm
(4 3/4 × 1 7/16 × 3 5/8 inches)
(w/h/d)
Mass (Approx.): 120 g (4.3 oz)
Operating temperature:
0 °C to +40 °C (32 °F to +104 °F)
Storage temperature:
–20 °C to +60 °C (–4 °F to +140 °F)
AC Adaptor AC-LS5
Input rating:
100 V to 240 V AC 50/60 Hz
Output rating:
4.2 V DC
See the label on the AC Adaptor for
other specifications.
Dimensions (Approx.):
48 × 29 × 81 mm
(1 15/16 × 1 3/16 × 3 1/4 inches)
(w/h/d, excluding projecting parts)
Mass (Approx.):
130 g (5 oz) excluding AC Power cord
Operating temperature:
0 °C to +40 °C (32 °F to +104 °F)
Storage temperature:
–20 °C to +60 °C (–4 °F to +140 °F)
Rechargeable battery pack NP-NH25
(supplied with DSC-ST80)
Normal voltage:
1.2 V × 2
Capacity:
typ. 2,500 mAh
Operating temperature:
0 °C to +40 °C (32 °F to +104 °F)](data:image/gif;base64,R0lGODlhAQABAIAAAAAAAP///yH5BAEAAAAALAAAAAABAAEAAAIBRAA7)