The super steady shot cyber-shot h1. featuring an amazing 12x optical zoom with optical image stabiliser, 5.1 effective megapixel resolution, with a superb large and bright 2.5” lcd screen. combines a real imaging processor and a host of photo features (2 pages)
Video: 1 Vp-p, 75 PRINT Image Matching III unbalanced, sync negative Compatible Audio: 327 mV (at a 47 k PictBridge Compatible load) Output impedance 2.2 k USB jack mini-B USB communication Hi-Speed USB (USB 2.0 compliant) DSC-H1 — 2 —...
Page 3
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
Electrical parts list of the SY-127 board are not SCHEMATIC DIAGRAM ···························· 4-19 shown. Pages from 5-14 to 5-18 are not shown. Shematic diagram of the CH-169 and SY-127 board are not shown. Pages from 4-21 to 4-44 are not shown. DSC-H1 — 4 —...
The electric shock is caused by the charged voltage which is kept without discharging when the main Wrap insulating tape. power of the DSC-H1 is simply turned off. Therefore, the remaining voltage must be discharged as described below. Preparing the Short Jig To preparing the short jig.
Page 6
• The type of memory stick that cannot be Replace the memory stick. used by this machine, is inserted. C:13:01 MS ERROR Format the memory stick with the DSC-H1. • Data is damaged. • Unformatted memory stick is inserted. Flash LED Checking of flash unit or replacement of...
1 Select [OK] with v on the control button, then press z. The message “Initialize all settings Ready?” appears. 2 Select [OK] with v, then press z. The settings are reset to the default setting. Make sure that the power is not disconnected during resetting. DSC-H1 1-3E...
8 Tapping screw (M1.7x4) black 2 Tapping screw (M1.7x4) black 9 Main section - 1 2 3 Two claws 4 MS-275 board 5 Battery connector 6 Three claws 7 Battery terminal board - 2 7 ST section (See page 2-3.) DSC-H1...
Page 9
4 Three harnesses (HA-001) (Red, White, Blue) 5 Open the ST cover in the direction of the arrow. 6 ST section Remove the AF-102 flexible board in the direction of the arrow. 2 Three claws 3 Three claws 4 AF-102 flexible board DSC-H1...
2. DISASSEMBLY 2. DISASSEMBLY 2-4. FLEXIBLE BOARDS LOCATION The flexible boards contained in the optical unit are not shown. CONTROL SWITCH BLOCK (SW51780) MS-029 SW-006 ST-001 FP-224 DSC-H1 2-8E...
Blue 3 Harness (H-001) ( 4 Apply the soldering in three points. 5 ST-123 board 6 ST-124 board claws 7 Four 8 ST cover 1 Red 9 Tapping screw (M1.7x4) black 3 Blue 0 ST section Blue White DSC-H1 HELP...
3. BLOCK DIAGRAMS Link Link OVERALL BLOCK DIAGRAM (1/2) POWER BLOCK DIAGRAM (1/2) OVERALL BLOCK DIAGRAM (2/2) POWER BLOCK DIAGRAM (2/2) DSC-H1...
Page 15
A/V OUT PITCH AD PITCH EVF BL LEV VIDEO AMP IC401 SENSOR AU LINE OUT SE402 PITCH/YAW XDD RST OUT SENSOR YAW AD SAN1 SO, SI, SCK SENSOR XSHIFT ON CN513 CN451 SW-447 BOARD (1/2) SW-006 FLEXIBLE FLAT CABLE (1/2) DSC-H1...
CAM 2.9V (TO PANEL) VFB4 D3.2V PSG4 G8 D001 (AF LED) XAF LED XAF LED PANEL 8.5V (6/11) CN507 IC802 CAM 3.2V -7.5V ON D821 VIDEO AMP D 3.2V A 3.2V, AU 3.2V, VI 3.2V, D 1.8V, D 1.2V DSC-H1...
EVF BL ON D001 (EVF BACK LIGHT) EVF BL LEV EVF BL L BACK LIGHT DRIVE LCD902 EVF BL H ST 5V L603 CN001 COLOR EVF PANEL 8.5V L602 PANEL VDD UNIT CAM_ 2.9V(TO PANEL) CN508 EV-016 FLEXIBLE BOARD DSC-H1 3-8E...
FP-224 FLEXIBLE BOARD (SY-CD RELAY) (FUNCTION SW) (SY-CD RELAY) SW-447 BOARD (2/2) SW-447 BOARD (2/2) CONTROL SWITCH BLOCK CONTROL SWITCH BLOCK (SW51780) (SW51780) (PITCH/YAW SENSOR AMP) (PITCH/YAW SENSOR AMP) COMMON NOTE FOR SCHEMATIC DIAGRAMS WAVEFORMS COMMON NOTE FOR SCHEMATIC DIAGRAMS WAVEFORMS DSC-H1...
Page 21
MOS IC. Replace only with part number Ne les remplacer que par une In addition, ensure that the receiver is not covered with specified. pièce portant le numéro spécifié. dusts nor exposed to strong light. DSC-H1...
Page 23
0 or dotted line with mark une marque 0 sont critiques STATIC_GND 0 are critical for safety. pour la sécurité. Replace only with part number Ne les remplacer que par une specified. pièce portant le numéro spécifié. DSC-H1 EV-016/MS-275/PL-039...
Page 24
0 or dotted line with mark une marque 0 sont critiques 0 are critical for safety. pour la sécurité. Replace only with part number Ne les remplacer que par une specified. pièce portant le numéro spécifié. DSC-H1 ST-123 4-10...
Page 27
REG_GND REG_GND REG_GND FP-224 FLEXIBLE BOARD is replaced as a block. So that this PRINTED WIRING BOARD is omitted. MS-029 FLEXIBLE FLAT CABLE is replaced as a block. So that this PRINTED WIRING BOARD is omitted. DSC-H1 AF-102/FP-224/MS-029 4-15 4-16...
Page 28
0 or dotted line with mark une marque 0 sont critiques LND003 REG_GND 0 are critical for safety. pour la sécurité. Replace only with part number Ne les remplacer que par une specified. pièce portant le numéro spécifié. DSC-H1 ST-001/ST-124/SW-006 4-17 4-18...
Page 29
So that this PRINTED WIRING BOARD is omitted. TO SY-127 BOARD(10/11) CN514 Schematic diagram of the CH-169 and SY-127 board (PAGE 4-41 OF LEVEL3) are not shown. Pages from 4-21 to 4-44 are not shown. DSC-H1 SW51780 4-19 4-20...
Page 35
RIGHT DUST D452 R412 S455 R405 R411 C405 R401 S460 S453 Q401 R453 RB452 CN452 1-867-125- Printed wiring board of the CH-169 and SY-127 board are not shown. Pages from 4-55 to 4-60 are not shown. DSC-H1 SW-447 4-53 4-54...
4.4 Vp-p 265 us 74 ns IC101 q; 7.7 Vp-p 265 us IC101 qs-qf 7.7 Vp-p 265 us IC101 qg 1.8 Vp-p 265 us Waveforms of the SY-127 board are not shown. Page 4-62 is not shown. DSC-H1 CD-576 4-61...
Page 39
In each case, u: , for example: uA...: A... , uPA... , PA... , uPB... , PB... , uPC... , PC... , uPD..., PD... Language that can be selected about SY-127 board Vietnam z z z z z z z z z DSC-H1...
0 are critical for safety. pour la sécurité. Danger of explosion if battery is incorrectly replaced. Replace only with part number Ne les remplacer que par une Replace only with the same or equivalent type. specified. pièce portant le numéro spécifié. DSC-H1...
(IC101 is not included in this COMPLETE board.) 1-867-126-11 FP-224 FLEXIBLE BOARD IC101 A-1122-935-A CCD BLOCK ASSY (CCD IMAGER) (IC101 is not included in this COMPLETE board of CD-576.) Be sure to read “Precautions upon replacing CCD imager” on page 4-1 when changing the CCD imager. DSC-H1...
6-501-154-01 DIODE NSCW455AT-TY5 CAUTION : ************************************************************ Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. Be sure to read “Precautions upon replacing CCD imager” on page 4-1 when changing the CCD imager. DSC-H1 5-11...
Page 49
Les composants identifiés par mark 0 or dotted line with mark une marque 0 sont critiques 0 are critical for safety. pour la sécurité. Replace only with part number Ne les remplacer que par une specified. pièce portant le numéro spécifié. DSC-H1 5-12...
< SENSOR > SE401 1-476-807-31 SENSOR, ANGULAR VELOCITY (PITCH) SE402 1-476-807-41 SENSOR, ANGULAR VELOCITY (YAW) ************************************************************ SY-127 BOARD, COMPLETE ********************** Electrical parts list of the SY-127 board are not shown. Pages from 5-14 to 5-18 are not shown. DSC-H1 5-13E...
Page 51
[Description of main button functions on toolbar of the Adobe Acrobat Reader Ver5.0 (for Windows)] Toolbar Printing a text Reversing the screens displayed once • To reverse the previous screens (operation) one by one, click 1. Click the Print button 2.