SPECIFICATIONS [System] [Input and Output connectors] Image device: USB communication: Hi-Speed USB DSC-S2100: 7.79 mm (1/2.3 type) (USB 2.0 compliant) R, G, B primary color mosaic filters [LCD screen] DSC-S2000: 7.70 mm (1/2.3 type) R, G, B primary color mosaic filters LCD panel: Total pixel number of camera: DSC-S2100: 7.5 cm (3.0 type)
Model information table Model DSC-S2000 DSC-S2100 US, CND, AEP, UK, E, US, CND, AEP, UK, E, Destination AUS, KR, BR AUS, CH, KR, BR • Abbreviation AUS : Australian model : Brazilian model : Chinese model CND : Canadian model : Korea model DSC-S2000/S2100 –...
ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPO- CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REM- NENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS PLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES...
1. SERVICE NOTE 1-1. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY 1-2. REGARDING FUSE The data can be copied/erased by the operations on the Setup screen. (When erasing the data, execute formatting the internal memory.) • MAIN BOARD Ref.NO: Note1: When replacing main board, erase the data in internal memory of the board before replacement.
2. REPAIR PARTS LIST IDENTIFYING PARTS (ENGLISH) NOTE: Follow the disassembly in the numerical order given. When indicating parts by reference • -XX, -X mean standardized parts, so they may have some differences from the original one. number,please include the board name. • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • The mechanical parts with no reference number in the exploded views are not supplied. The components identified by mark 0 or • Due to standardization, replacements in the parts list may be different from the parts speci- dotted line with mark are critical for safety. fied in the diagrams or the components used on the set. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
NOTE FOR REPAIR • Make sure that the flat cable and flexible board are not cracked of Cut and remove the part of gilt bent at the terminal. which comes off at the point. Do not insert the cable insufficiently nor crookedly. (Be careful or some pieces of gilt may be left inside) • When remove a connector, don’t pull at wire of connector. It is pos- sible that a wire is snapped. • When installing a connector, don’t press down at wire of connector. It is possible that a wire is snapped. • Do not apply excessive load to the gilded flexible board. DISCHARGING OF THE CHARGING CAPACITOR The charging capacitor is charged up to the maximum 315 V Note: Note:...
Page 8
2-1. EXPLODED VIEWS DISASSEMBLY 1(Claw) 2-1-1. OVERALL SECTION 1. Remove to numerical order ( ) in the left figure. (Note1) 1� #S2 / #S4 X 7 Left View Right View Bottom View 5� (Note1) DSC-S2000 Main Frame Section (See Page 2-4) (Note1) BT Lid Open (2) →...
2-1-2. MAIN FRAME SECTION DISASSEMBLY ns: not supplied 1. Remove to numerical order ( ) in the left figure. #S5 X 4 Front View Top View Back View DSC-S2000 9� Protection Sheet Remove #S1 X 2 Right View Top View DISCHARGING OF THE CHARGING CAPACITOR DSC-S2100 9�...
2-1-3. LENS SECTION DISASSEMBLY ns: not supplied 1. Remove to numerical order ( ) in the left figure. #S3 X 3 Back View Note (CCD Assy) Note: Be careful about the Lens Block Assy. (Note) Don't press the Barrier part � 102 (Note) Be careful of the Weld �...
3. ASSEMBLY Assembly-1: Routing harness of Main Frame Sub Assy Checking supplied accessories. DSC-S2000 BATT-1 BATT+1 Note: This item is supplied with the unit as an accessory, but is not prepared as a service part. LR6 (size AA) alkaline batteries (Note) Instruction Manual ・ (Only for destination Japanese model) 日本語・英語・韓国語・中国語のみ部品供給可能です。 4-170-175-11 (SIMPLIFIED CHINESE) Main Board Main Frame Sub Assy 4-170-176-11 (ENGLISH) ∗...